Body Wraps & Weight Loss
Body wraps can help tone and tighten the skin, improve blood circulation, detoxify the body and help mobilize fat so it can be eliminated from the body naturally. You do not need any special equipment other than a mixing bowl, heating pot and wrapping sheets like thin towels.
Body wraps work in two stages: absorption and squeezing (compaction). In the absorption stage you apply a substance on your body by “wraps”. Once the pores of skin are opened, the fluids are “extracted” or “absorbed” by the substance and the bandage.
There are several absorbents: sea clay, seaweed, herbal, mineral and aloe vera. The effect of the wrap is determined by the ingredients used.
Squeezing is simply compacting the tissues together after the “interstitial fluid” has been extracted. Once the fluids have been extracted, there are empty “pockets” between the cells. So if somehow we can squeeze them closer together, the end result should be a thinner and leaner looking body. The body bandages and body wraps squeeze the body part and squeezing together the empty “pockets”.
A simple body wrap can be a mixture of a clay and some salt. A more complex wrap contains herbs, essential oils and nutritive ingredients. The exact proportions of ingredients are not important but the repeated use will be useful.
How To Build a Ferret Cage - 3 Things You Need To Remember
If you decide to build a cage for your ferret, you have to remember a few things. Otherwise your ferret will not be safe in its new home or will find it a gloomy place to stay.
Building a ferret cage - things to consider:
1. Use a metal tray for the bottom of the cage. This will make the cage sturdier and allow it to withstand all of your ferret’s running around inside. You need to create a softer flooring on top of the metal tray. Vinyl is a good material for that.
2. Make sure your ferret cage has enough room for the following things: litter, toys, food and water dishes, and enough space for your ferret to run around in. Remember, this is your ferret’s home. It needs to be comfortable. Many people go for multi-level ferret cages as it saves room around the house.
3. Make sure there are no sharp edges in your cage. Once you create the cage, make sure that none of the metal bars have any protruding points or sharp edges or your ferret may injure itself. If need be, use duct tape to secure all corners and sharp edges.
4. Don’t forget to leave room for a door (I know this seems obvious, but some people forget this until the last minute), and make sure it’s large enough.
5. Make sure that the food and water dishes are secure and in a position in which it’s easy to sip or eat from, but impossible to turn over.
6. Use recycled paper or wood pellets as the base of the litter box as these 2 materials are great absorbents and hold a minimum of bad odor.
7. Make sure you place some ferret toys inside the cage. Ferrets are playful creatures and need something to occupy them. Ferrets need toys which they can’t chew off. Get some specific Ferret toys and place them in the cage.
I hope you have fun building your ferret cage, and that your pet will enjoy its stay there.
Plant Maintenance Best Management Practices
Plant Maintenance managers seek to effectively utilize existing resources to reduce operating costs and save money that increases the bottom line of the company. The role of an effective plant maintenance operation is to consistently maintain quality pollution prevention control measures at all times
The segment of plant management that is most susceptible to pollution control fines is in the area of landscape maintenance. Each raindrop or the run off from watering that falls on impervious surfaces such as pavement, sidewalks, and roads, can mobilize pollutants on those surfaces.
Everything from automobile oil and grease to trash and debris can be carried by runoff into lakes, streams, rivers and oceans. Oil and chemical spills that form on pavement pose a significant environmental threat. Oil and chemical spills run into waterways and threaten valuable ecosystems. These spills also threaten public health and safety.
The following pollution control prevention principles and practices apply to most industries but the following guidelines are specific to the areas of plant maintenance. The Best Management Practice Objectives are the minimum standards that are set by the EPA.
* When it is possible, the company should use alternative, safer or recycled products that have the least negative environmental impact.
* A comprehensive plan to redirect storm water.
* An overall plan to reduce the use of water and use recycled water.
* Reduce storm water flow across the site of the facility.
* Recycle or reuse water waste products.
* Move or cover potential pollution run off from storm water contact.
* Provide training to employee in pollution prevention.
The Best Management Practices for facilities’ maintenance that reduces or eliminates pollution include:
1. Reduction of landscape maintenance requirements
* Use low water use flowers, trees, shrubs and ground covers.
2. Properly store and dispose of gardening wastes
* Grass clippings, leaves, sticks, or other collected vegetation should be disposed of as garbage at a permitted landfill or by composting.
3. Use erosion control measures.
* When chemicals or oil are spilled on impervious surfaces, they should be cleaned up immediately with non-toxic cleaners or absorbents.
* Use Peat Moss as an environmentally safe method to clean impervious surfaces.
* Peat Moss Absorbents passed the T.C.L.P. (Toxic Characteristic Leachate Procedure)
* Peat Moss has an affinity for hydrocarbons of all types
4. Proper Management of irrigation and runoff
* Do not allow muddy water into a storm drain.
* Pour the muddy water over landscaped areas.
* Plant managers should check irrigation system regularly for leaks
* Insure that excessive runoff is not occurring from their facilities.
5. Proper storage and disposal of chemicals
* Implement storage requirements for pesticide products
* Confer with the local fire department or Agricultural commissioner on storage
6. Proper management of pesticide and herbicides
* Do not apply pesticides if rain is expected
* Do not apply pesticides if the wind speed exceeds 5 MPH
* Pesticides should not be mixed or prepared near storm drains
7. Proper use and management of fertilizer includes:
* Follow manufacturer’s recommendations and label directions.
* Use techniques that minimize off target applications of fertilizer
* Use alternative application techniques.
8. Train employee in the implementation of Best Management Practice procedures and guidelines.
* The training should include storm water discharge prohibitions and waste water discharge requirements.
* Train employees on the use of pesticides and pesticide applications.
* Establishing a training schedule that provides employees with the proper tools and knowledge to immediately begin cleaning up a spill.
Applying Best Management Practices (BMPs) insure that facilities are in compliance with local, state and national environmental control regulations. Employees who are trained properly are a critical factor in implementing these guidelines. The site’s spill control plan and proper spill cleanup procedures should be an ongoing implementation project.
Discover What Boating Supplies You Need To Control Oil Spills
If you are a boater you will eventually experience an oil spill or see one as you transverse across the water. There are positive responses to this tragedy by taking quick decisive action. These spills can be contained with quick action and the right equipment.
Any discharge of a petroleum product that produces a sheen or discoloration on the water surface is a violation of the U. S. Water Pollution Act. Even when you witness a spill, you are required by law to report it to the Coast Guard.
If you fail to report a spill, you may be cited and face some legal ramifications. If it is your vessel that causes the spill, there are some immediate actions that you can take to control the spill.
Once you have identified the source of the spill, contain the spill at the source. There may be several causes for the spill, but finding the source is critical. In many instances, it is a fuel line, or refueling, caps sometimes come lose or the filters may need to be adjusted.
Once you have control of the source of the spill, you must prevent the oil from leaving your boat. You should always carry special absorbent materials that can help control and eliminate the sheen if it should develop.
Some oil only absorbents that should always be available onboard include: Oil only absorbent pads, sweeps and socks which can be drawn over the water surface to absorb broad sheens or surface spills. This is a great way to quickly clean up oil spill on water because oil only absorbents do not sink.
The Fuel or oil in the water or on the boat can be picked up with special oil absorbent socks that specifically designed to absorb up to 15 times their weight in oil spills and are non-biodegradable. Oil Absorbent Socks repel water and only absorb oil-based fluids. The Oil Absorbent Socks are great for this applications.
Do not use soap or detergent to cleanup an oil spill on the water. The soap only causes the oil to sink and concentrate at the bottom. After the excitement of controlling and containing a spill properly, take the time necessary to report it to the Coast Guard.
Take immediate action to control, clean up, and report a spill. Be sure the spill is resolved correctly and that you have acted responsibly. With the proper products and prompt action, our waterways will be protected.
The Best Absorbents for Spill Cleanup And Control
There are so many types and quality of absorbents on the market, that companies may find themselves inundated with high priced products that do not address their specific industry or requirement. Finding the right absorbents for the right applications is an ongoing challenge for companies who require effective products to control spills and storm water issues.
The best solutions for environmental compliance issues require that companies have adequate inventory of these products that effectively address the environmental compliance challenges for spills and cleanup.
Absorbents are a small segment of the spill containment products that are designed to address environmental issues. Absorbents represent a cost effective way to manage and control liquid spills, leaks and fast cleanup.
Absorbent pads are designed for specific applications and can also enhance the cleanliness of a workplace environment. A variety of absorbent pads are available that fits a specific type and size of spill.
Some of the Absorbent Product available includes:
Universal Gray Absorbent Pads (Most Popular) hide grunge with their gray color will foster longer use. These absorbent pads were made to absorb both oil and water based fluids. Maintenance repair shops, manufacturing facilities, municipalities and many more users have made our universal absorbent pads our best seller.
Oil Only White Absorbent Pads (Repels Water) absorb oil on water or for outside applications. These absorbent pads were made to absorb oil and repel water-based fluids.
Oil Only White Absorbent Pads are used successfully in the following industries:
*Marine industry
*Petroleum industry
*Outside facilities
Hazmat Yellow Chemical Absorbent Pads (For Aggressive Fluids) are designed to absorb aggressive or unknown fluids. These absorbent pads are a caution yellow color for safety and bring awareness to individuals who might wander into a dangerous spill area.
Industries that use these types of Absorbent Pads include:
*Chemical industry
*Manufacturing facilities
HAZMAT absorbent pads are a critical component of their spill control program
Universal Spill Cleanup Absorbent Pads absorbs oil, oil-based products, and water (all liquids). These pads are made of polypropylene. Absorbent pads clean up messy drips, leaks and over spray of fluids quickly. One pad absorbs approximately a ½ quart of oil, and pads can withstand hot oil up to 210°F.
Some of the applications for this product are:
*Placement under vehicles
*Under machines
*Under equipment
*Placed in the bilge of boats
This product helps in absorbing spills and can be used as well to wipe oily hands and clean oily tools.
Static Resistant Oil Only Pads and Rolls are used around flammable liquids and where static electricity poses a hazard. These pads are suitable for arctic and desert climates. Static resistant pads are great for diesel fuels. These pads repel water-based liquids. They are sold by the case or roll.
Absorbent universal socks are the best choice for industrial applications. These general purpose Absorbent socks absorb both oil and water base liquids and drips.
Easy to mold and shape around leaky equipment and machinery. Universal absorbent socks are primarily effective for oils, coolants, solvents and water. These absorbent socks absorb 1 gallon of liquid per sock (4 ft. size). These socks are used to absorb leaks and drips around the bases of machinery.
Storm Water Management Products
Keeping track of the evolving world of storm water regulations can be daunting tasks for industries that must adhere to these changing regulations. Adapting storm water programs and products that are approved to address specific area of pollution is an ongoing operational requirement.
The statues on the municipal level might impose stricter standards and schedules for industrial and municipal storm water control that are geographically specific.
However the national standard is consistent and is known as the National Pollutant Discharge Elimination System (NPDES). The permitting program controls pollutants discharged into surface water such as lakes, ponds, streams and even the ocean.
Phase I of NPDES was designed for cities with populations of more than 100,000. The NPDES also targeted large industrial and construction sites. The statues required that industries and construction sites begin treating storm water runoff from their locations.
Phase II of NPDES was announced in December 1999 and required that more than 5,000 municipalities and all new developments one acre or larger implement BMP’s for stormwater treatment to the maximum extent that was practical. Specialty products are available that help companies comply with NPDES statues.
Storm Drain Products
Oil leaks from vehicles in parking lots can be managed effectively with drain filters and drain covers. Drain filters and covers are simple devices designed to remove waste from storm water before it can become a problem in the water system. Filter inserts and storm drain covers help companies comply with NPDES, 40 CFR 122.26 (1999) when used within the Best Management Practice stipulated in Storm Water Pollution Prevention Plans.
These types of product are useful for:
*Industrial Facilities - keep oil and other contaminants from entering storm drains.
*Construction Sites - capture eroded soil and wind-blown debris.
*Parking Lots - collect oil, fuel and other contaminants that drip from cars.
Held in place by a metal grate, filter products can effectively remove coarse sediments, oil, grease, litter and debris from storm water. Parking lots tend to be sources of oil, hydrocarbons and other water pollution. Cars and trucks drip oil and grease on to the surface of the cement or asphalt and is carried into the catch basins by rainwater.
Most of these catch basins ultimately drain into streams, lakes, or ground water aquifers. A drain filter works great for parking lots, vehicle storage/service areas, construction sites and industrial plants. Because these areas produce large amounts of sediments, oil, and other pollutants, the EPA has very stringent requirements that are imposed on these types of sites.
A major concern for the EPA is the oil that can be transferred to catch basins and storm drains. Industrial locations must exercise extreme caution to prevent oil from getting to these areas. Oil skimmers and absorbents are useful in providing a solution for these problems. Companies that produce these waste comply with NPDES, 40 CFR 122.26 (1999) by preventing pollution at its source.
Stormwater Management Products are a key component in the compliance and implementation of EPA’s Clean Water Act. The overriding concern and utility of these storm water products is to protect the quality of U.S. waterways by reducing the discharge of sediment, oil and chemicals into storm drains, surface water and groundwater.
The Best Absorbents for Spill Cleanup And Control
There are so many types and quality of absorbents on the market, that companies may find themselves inundated with high priced products that do not address their specific industry or requirement. Finding the right absorbents for the right applications is an ongoing challenge for companies who require effective products to control spills and storm water issues.
The best solutions for environmental compliance issues require that companies have adequate inventory of these products that effectively address the environmental compliance challenges for spills and cleanup.
Absorbents are a small segment of the spill containment products that are designed to address environmental issues. Absorbents represent a cost effective way to manage and control liquid spills, leaks and fast cleanup.
Absorbent pads are designed for specific applications and can also enhance the cleanliness of a workplace environment. A variety of absorbent pads are available that fits a specific type and size of spill.
Some of the Absorbent Product available includes:
Universal Gray Absorbent Pads (Most Popular) hide grunge with their gray color will foster longer use. These absorbent pads were made to absorb both oil and water based fluids. Maintenance repair shops, manufacturing facilities, municipalities and many more users have made our universal absorbent pads our best seller.
Oil Only White Absorbent Pads (Repels Water) absorb oil on water or for outside applications. These absorbent pads were made to absorb oil and repel water-based fluids.
Oil Only White Absorbent Pads are used successfully in the following industries:
*Marine industry
*Petroleum industry
*Outside facilities
Hazmat Yellow Chemical Absorbent Pads (For Aggressive Fluids) are designed to absorb aggressive or unknown fluids. These absorbent pads are a caution yellow color for safety and bring awareness to individuals who might wander into a dangerous spill area.
Industries that use these types of Absorbent Pads include:
*Chemical industry
*Manufacturing facilities
HAZMAT absorbent pads are a critical component of their spill control program
Universal Spill Cleanup Absorbent Pads absorbs oil, oil-based products, and water (all liquids). These pads are made of polypropylene. Absorbent pads clean up messy drips, leaks and over spray of fluids quickly. One pad absorbs approximately a ½ quart of oil, and pads can withstand hot oil up to 210°F.
Some of the applications for this product are:
*Placement under vehicles
*Under machines
*Under equipment
*Placed in the bilge of boats
This product helps in absorbing spills and can be used as well to wipe oily hands and clean oily tools.
Static Resistant Oil Only Pads and Rolls are used around flammable liquids and where static electricity poses a hazard. These pads are suitable for arctic and desert climates. Static resistant pads are great for diesel fuels. These pads repel water-based liquids. They are sold by the case or roll.
Absorbent universal socks are the best choice for industrial applications. These general purpose Absorbent socks absorb both oil and water base liquids and drips.
Easy to mold and shape around leaky equipment and machinery. Universal absorbent socks are primarily effective for oils, coolants, solvents and water. These absorbent socks absorb 1 gallon of liquid per sock (4 ft. size). These socks are used to absorb leaks and drips around the bases of machinery.
Absorbents - Simple Solution to Marinas’s Pollution Problems
Marinas provide an economic as well as a recreational benefits to society as a whole. As as result of the popularity of boating and other waterbased activities, Marina’s fueling docks are high traffic areas and generate large amounts of hazardous petroleum based products.
Marina owners are required to maintain an effective spill prevention plan which includes environmental safeguards that prevent the degradation of the water systems.
There are a variety of technologies and products that are available that can help this industries prevent or at least mitigate several of these inherent environmental concerns. Most marina owners practice an aggressive environmental protection program in the areas of oil spill containment.
It is sometimes the most inconsequential products that can produce the biggest impact. Absorbents represent that inconsequential product. Absorbents are the quick solution that many marinas use for cleaning up oil spills. Absorbents are used in many spill situations on land as well as in and around these water dependent industries because of the ease of use.
Absorbents are a general category of products that include a unique subcategory of special types of absorbents for the marine industry. Booms, sweeps, socks and bilges are the most commonly used. These absorbent products are functional for the marine industry because they can be quickly, safely and effectively deployed to contain spills.
Oil absorbent booms are perfect for marine spill containment. These oil absorbent booms are constructed with a strong mesh outer skin that encases a highly absorbent polypropylene filler. Oil only absorbent booms are ideal for collecting oil quickly when a boat is fueling and oil accidentally spills into the water.
A marine operator can toss the boom into the water, collect the spill quickly and then retrieve the boom. The booms are of course water repellent.
Bilge socks are flexible absorbents that can be shaped to accommodate the shape of spills. It is important to select absorbents based on their intended use. Marinas traditionally opt to use oil absorbents that only absorb oil-based fluids. But there are absorbents that an also absorb water based or chemical spills.
Oil absorbent sweeps are used often by marine operators to absorb broad sheens or surface spills.
Absorbents are just one of the many variety of products designed to contain and manage oil spills. The special needs of marinas require that they properly use several methodologies for effective hazardous waste management. To stay within the compliance guidelines, marinas are required to adhere to Title 40 Code of Federal Regulations Part s 260-268 (see Hazardous Waste Management, page 39).
When spills occur in a marina, the management of the marina should be notified immediately. Marina operators are usually very conscientious concerning containing oil spills within their environment. In fact, many marina operators, all across the United States have joined forces in an effort to use Best Practices in Marine Environmental Management to insure the safety of the waterways.
These individual marina operations practice strict adherence to the clean marina guidelines. Absorbents when used properly play a major role in this initiative.
How Simple Absorbents Help Marinas Comply With Federal Regulations
There are many marine facilities operating in the USA today. Millions of people use the waterways daily for recreational and commercial activities. It is estimated that marine recreational activities contributes more than US $30 billion to the US economy each year, while supporting nearly 300,000 jobs in the manufacturing, retail, and service sectors.
This industry includes marinas, boatyards, marine retailers, recreational and commercial vehicles. Clean water is an essential resource for this industry. Without clean water this multi-billion dollar industry will cease to exist.
Marinas and boating enthusiasts often use various levels of preventive equipment and products to keep the waters safe and avoid costly spills. Oil absorbents pads are one way to contain oil spills on the water. This simple product can be used for environmental spill cleanup and remediation purposes by marinas and boaters.
There are economic benefits realized by marina managers who implement preventative safety measures. Products that improve the efficiency of these operations are in high demand. Boatyards and marinas are in constant need of bilge containment products.
The marinas as well as boatyards generate special wastes such as bilge water, used oil, used oil filters. Other contaminated materials include old gasoline, hazardous wastes such as acetone, paint and washing solvents. These industries are required to use products that are environmentally safe and specifically designed to contain and manage oil spills.
The products that are used to contain the spills also must be managed and disposed of in a prescribed manner. The methods of this type of disposal is outlined in Title 40 Code of Federal Regulations Parts 260-268 (see Hazardous Waste Management, page 39)
To help boaters, marinas and boatyards comply with the various pollution control and water safety regulations; spill control materials and special containers for emergency clean up are available from commercial suppliers.
The choices for these types of containers include flexible-sidewall portable spill containment berms that are the easiest to use. This flexible sidewall equipment can provide an affordable hazardous material storage unit. Berms provide incidental spill control during temporary storage of drums, machine parts, tanks and generators. Berms can also be used in other capacities as a wash down pad or pumping station.
A mobile storage or spill containment unit is always the preferred choice. A mobile unit is a cost as an alternative to hard plastic pallets. The hard plastic pallets need to be moved by a forklift. These pallets are always bulky and take up valuable space. Portable spill containment berms eliminates the need for bulky hard plastic pallets.
Marina Owners should always provide a spill contingency plan that list the specific products required to operate their facilities in the safest manner possible. The second element of the spill contingency plan is training of employees who will respond to the spill.
This plan is always required to be in written form and updated on a yearly basis. The plan can be updated more frequently if required. This spill containment plan is part of a total safety quality control plan. The marina/boatyard’s fueling contingency plan provides a list of products and procedures to handle incidental spills quickly and safely. Products that are EPA sanctioned are always the best defense against uncontrolled spills that could harm the safety of our waterways.
Absorbents - Simple Solution to Marinas’s Pollution Problems
Marinas provide an economic as well as a recreational benefits to society as a whole. As as result of the popularity of boating and other waterbased activities, Marina’s fueling docks are high traffic areas and generate large amounts of hazardous petroleum based products.
Marina owners are required to maintain an effective spill prevention plan which includes environmental safeguards that prevent the degradation of the water systems.
There are a variety of technologies and products that are available that can help this industries prevent or at least mitigate several of these inherent environmental concerns. Most marina owners practice an aggressive environmental protection program in the areas of oil spill containment.
It is sometimes the most inconsequential products that can produce the biggest impact. Absorbents represent that inconsequential product. Absorbents are the quick solution that many marinas use for cleaning up oil spills. Absorbents are used in many spill situations on land as well as in and around these water dependent industries because of the ease of use.
Absorbents are a general category of products that include a unique subcategory of special types of absorbents for the marine industry. Booms, sweeps, socks and bilges are the most commonly used. These absorbent products are functional for the marine industry because they can be quickly, safely and effectively deployed to contain spills.
Oil absorbent booms are perfect for marine spill containment. These oil absorbent booms are constructed with a strong mesh outer skin that encases a highly absorbent polypropylene filler. Oil only absorbent booms are ideal for collecting oil quickly when a boat is fueling and oil accidentally spills into the water.
A marine operator can toss the boom into the water, collect the spill quickly and then retrieve the boom. The booms are of course water repellent.
Bilge socks are flexible absorbents that can be shaped to accommodate the shape of spills. It is important to select absorbents based on their intended use. Marinas traditionally opt to use oil absorbents that only absorb oil-based fluids. But there are absorbents that an also absorb water based or chemical spills.
Oil absorbent sweeps are used often by marine operators to absorb broad sheens or surface spills.
Absorbents are just one of the many variety of products designed to contain and manage oil spills. The special needs of marinas require that they properly use several methodologies for effective hazardous waste management. To stay within the compliance guidelines, marinas are required to adhere to Title 40 Code of Federal Regulations Part s 260-268 (see Hazardous Waste Management, page 39).
When spills occur in a marina, the management of the marina should be notified immediately. Marina operators are usually very conscientious concerning containing oil spills within their environment. In fact, many marina operators, all across the United States have joined forces in an effort to use Best Practices in Marine Environmental Management to insure the safety of the waterways.
These individual marina operations practice strict adherence to the clean marina guidelines. Absorbents when used properly play a major role in this initiative.